Vinnie Rossi

CANTA

Vinnie Rossi completes CANTA range with preamp and power amp

The new separates follow the CANTA Phono Preamplifier and CANTA Integrated Amplifier. They put the integrated model’s Class A valve linestage and Class AB MOSFET output stage in separate chassis.

Georg S. Kuklick

•

Vinnie Rossi has launched a preamplifier and matching stereo power amplifier to complete its CANTA range. The CANTA Preamplifier uses one Tung-Sol 6SN7 triode section per channel for voltage gain. The CANTA Stereo Power Amplifier is rated at 125 W per channel into 8 Ω and 250 W per channel into 4 Ω, and is stable into loads as low as 2 Ω.

The power amplifier uses two pairs of matched lateral MOSFETs in each channel of its dual-mono output stage. The transistors mount directly to a solid aluminium billet that serves as their heatsink. A board above the output stages carries the fully balanced input and driver circuits. A separate shielded chamber houses the switch-mode power supply, which uses active power factor correction and has a peak rating of 1,200 W.

The preamplifier’s dual-mono linestage has a dedicated switch-mode power supply with power factor correction and Belleson-regulated outputs. A 100-step resistor ladder controls volume. Each input stores its own gain setting of 0, 6 or 12 dB and its own balance setting, with 12 steps of left-to-right adjustment.

The preamplifier has four stereo line inputs, two on balanced XLR pairs and two on single-ended RCA pairs. Both formats are also available as volume-controlled line outputs. The front-panel LCD menu provides access to Home Theater Bypass. Trigger outputs switch compatible components on or off with the preamplifier, and the power amplifier has a 3.5 mm trigger connection for coordinated power-up.

Both components have chassis machined from solid aluminium, then bead-blasted and anodised. The preamplifier houses its valves inside the enclosure and comes with a solid-aluminium infrared remote. It is made in the USA and carries a ten-year warranty.

Key specifications

CANTA Preamplifier — linestage

Dual-mono Class A; one Tung-Sol 6SN7 triode section per channel for voltage gain

CANTA Preamplifier — power supply

Dedicated switch-mode supply with power factor correction and Belleson super-regulated outputs

CANTA Preamplifier — volume control

100-step resistor ladder

CANTA Preamplifier — gain

Low: 0 dB; medium: 6 dB; high: 12 dB; selectable per input

CANTA Preamplifier — balance

12-step left-to-right adjustment; setting saved per input

CANTA Preamplifier — frequency response

5 Hz–100 kHz, ±0.5 dB

CANTA Preamplifier — THD+N

<0.1%, 20 Hz–20 kHz

CANTA Preamplifier — signal-to-noise ratio

>100 dB, 20 Hz–20 kHz

CANTA Preamplifier — input impedance

47 kΩ

CANTA Preamplifier — line output impedance

<100 Ω

CANTA Preamplifier — line inputs

2 balanced XLR pairs; 2 single-ended RCA pairs

CANTA Preamplifier — line outputs

Volume-controlled balanced XLR and single-ended RCA

Data Source

Never miss an update!

Subscribe for platform news and what lands next.

By clicking Subscribe Now you're confirming that you agree with our Terms & Conditions.

Built by humans with the help of AI in Berlin, New York, and Vienna.

© 2026 Neo Digital Magazines llc. All rights reserved.

Never miss an update!

Subscribe for platform news and what lands next.

By clicking Subscribe Now you're confirming that you agree with our Terms & Conditions.

Built by humans with the help of AI in Berlin, New York, and Vienna.

© 2026 Neo Digital Magazines llc. All rights reserved.

Never miss an update!

Subscribe for platform news and what lands next.

By clicking Subscribe Now you're confirming that you agree with our Terms & Conditions.

Built by humans with the help of AI in Berlin, New York, and Vienna.

© 2026 Neo Digital Magazines llc. All rights reserved.